Product Description
Product Description
80E RV Series gear ratio 57:1 Cycloidal Pin Wheel Reducer robot gearbox For Cobot
Cycloidal Pin Wheel Reducer robot gearbox Installed with radial thrust ball bearings, so it can support external load, torque rigidity, large allowable torque, can reduce the number of components required, easy installation. The revolution speed of WRV gears is slower and vibration is reduced, which can reduce the motor structure (input gear) and inertia.
Cycloidal Pin Wheel Reducer robot gearbox High precision, high rigidity, high torque, high load and other characteristics realize hollow design at the same time. After being hollowed out, the ease of use of the product is improved due to the variety of piping and cable layout options.
The Cycloidal Pin Wheel Reducer robot gearbox is developed on the basis of the traditional needle wheel reducer. It not only overcomes the shortcomings of the general needle pendulum transmission, but also has more advantages, such as long life, stable precision, high efficiency, smooth transmission, small size, Light weight, large reduction ratio range, etc. This RV reducer from FUBAO adopts a double support support mechanism and a pinwheel mechanism, even if a torque up to 6 times the rated torque is applied, the product will not be damaged, and the torsional rigidity is very large. Small backlash, small volume, large torque. In order to directly support large loads, main bearings (large angular contact ball bearings) are installed inside.
Cycloidal Pin Wheel Reducer robot gearbox mainly has the following characteristics:
A. Main bearing built-in mechanism
1. Improved reliability;
2. Total cost reduction;
3. Radial thrust ball bearings are installed, so they can support external loads, and the moment rigidity and allowable moment are large, which can reduce the number of required components;
4. The use of couplings and motor flanges makes the installation of the motor very simple.
B. 2-stage deceleration mechanism
1. Small vibration;
2. The revolution speed of the gear is slowed down, the vibration is reduced, and the direct connection part of the motor (input gear) can be reduced, and the inertia can be reduced.
C. Double column support mechanism
1. High torsional rigidity;
2. Strong impact resistance;
3. The crank shaft is supported by double columns in the reducer.
D. Rolling contact mechanism
1. Excellent starting power;
2. Small abrasion and long service life;
3. Small backlash (1arc.min).
Product Parameters
| WRV-E series | Specifications | WRV6E | WRV20E | WRV40E | WRV80E | WRV110E | WRV160E | WRV320E | WR450E |
| Rated output torque | 196 | 882 | 1666 | 2156 | 2940 | 3920 | 7056 | 17640 | |
| Reduction ratio | 31~103 | 57~161 | 57~153 | 57~153 | 81~175 | 81~171 | 81~185 | 81~192 | |
| Backlash | <=1 | ||||||||
Detailed Photos
Application Case
Company Profile
HangZhou Fubao Electromechanical Technology Co., Ltd. was established in 2008, the company has a complete precision reducer design, production capacity. Set R & D, manufacturing, assembly and sales, more in the field of gear manufacturing has more than 10 years of background, in the manufacturing equipment is equipped with Switzerland Riesenhahl gear grinding machine, domestic Qinchuan gear grinding machine, hamai gear hobbing machine and domestic Xihu (West Lake) Dis. gear hobbing machine, Japan Yasaki TLGmazak CNC lathe, CNC milling machine and other fully CNC equipment, In addition, it is equipped with other advanced measuring equipment such as Japanese TTI gear detector, 3 coordinate measurement, reducer backlash measurement instrument and so on. In a strong manufacturing capacity at the same time, can be stable, continuous manufacturing of high-quality precision reducer products.
The precision reducer produced by our company has the characteristics of high structural rigidity, small back backlash, precise transmission and so on. It is widely used in various industries. Companies adhering to the concept of let customers participate in manufacturing, and strive to provide customers with more personalized services. In the field of precision transmission has a unique achievements. It is our CZPT pursuit to make far-reaching contributions.
Factory Display
FAQ
Q: Speed reducer grease replacement time
A: When sealing appropriate amount of grease and running reducer, the standard replacement time is 20000 hours according to the aging condition of the grease. In addition, when the grease is stained or used in the surrounding temperature condition (above 40ºC), please check the aging and fouling of the grease, and specify the replacement time.
Q: Delivery time
A: Fubao has 2000+ production base, daily output of 1000+ units, standard models within 7 days of delivery.
Q: Reducer selection
A: Fubao provides professional product selection guidance, with higher product matching degree, higher cost performance and higher utilization rate.
Q: Application range of reducer
A: Fubao has a professional research and development team, complete category design, can match any stepping motor, servo motor, more accurate matching.
|
Shipping Cost:
Estimated freight per unit. |
To be negotiated |
|---|
| Application: | Motor, Machinery, Agricultural Machinery, Robot Arm |
|---|---|
| Function: | Distribution Power, Change Drive Torque, Speed Changing, Speed Reduction, Speed Increase, Lower Rpm and Increase Torque |
| Layout: | Cycloidal |
| Customization: |
Available
| Customized Request |
|---|
A Mathematical Model of a Cycloid Gearbox
Having a gearbox with a cycloidal rotor is an ideal design for a car or any other vehicle, as the cycloidal design can reduce the amplitude of vibration, which is a key component in car performance. Using a cycloidal gearbox is also a great way to reduce the amount of friction between the gears in the gearbox, which can help to reduce noise and wear and tear. A cycloidal gearbox is also a very efficient design for a vehicle that needs to perform under high loads, as the gearbox can be very robust against shock loads.
Basic design principles
cycloidal gearboxes are used for precision gearing applications. Cycloidal drives are compact and robust and offer lower backlash, torsional stiffness and a longer service life. They are also suitable for applications involving heavy loads.
Cycloidal drives are compact in size and provide very high reduction ratios. They are also very robust and can handle shock loads. Cycloidal drives are ideally suited to a wide range of drive technologies. Cycloidal gears have excellent torsional stiffness and can provide a transmission ratio of 300:1. They can also be used in applications where stacking multiple gear stages is not desired.
In order to achieve a high reduction ratio, cycloidal gears must be manufactured extremely accurately. Cycloidal gears have a curved tooth profile that removes shear forces at any point of contact. This provides a positive fit for the gear disc. This profile can be provided on a separate outer bushing or as an internal gear profile insert.
Cycloidal drives are used in marine propulsion systems, where the load plate rotates around the X and Y axis. The plate is anchored by a threaded screw hole arranged 15mm away from the center.
A secondary carrier body is used in a cycloidal gearbox to support the load plate. The secondary carrier body is composed of a mounting carrier body and a secondary carrier disc.
Low friction
Several studies have been conducted to understand the static problems of gears. In this paper, we discuss a mathematical model of a low friction cycloidal gearbox. This model is designed to calculate various parameters that affect the performance of the gearbox during production.
The model is based on a new approach that includes the stiction effect and the nonlinear friction characteristic. These parameters are not covered by the conventional rule of thumb.
The stiction effect is present when the speed direction is changed. During this time, the input torque is required to prevail over the stiction effect to generate movement. The model also enables us to calculate the magnitude of the stiction effect and its breakaway speed.
The most important thing is that the model can be used to improve the dynamic behavior of a controlled system. In this regard, the model has a high degree of accuracy. The model is tested in several quadrants of the gearbox to find the optimum stiction breakaway speed. The simulation results of the model show that this model is effective in predicting the efficiency of a low friction cycloidal gearbox.
In addition to the stiction model, we also studied the efficiency of a low friction cycloidal reducer. The reduction ratio of this gearbox was estimated from the formula. It is found that the ratio approaches negative infinity when the motor torque is close to zero Nm.
Compact
Unlike standard planetary gears, cycloidal gearboxes are compact, low friction and feature virtually zero backlash. They also offer high reduction ratios, high load capacity and high efficiency. These features make them a viable option for a variety of applications.
Cycloid disks are driven by an eccentric input shaft. They are then driven by a stationary ring gear. The ring gear rotates the cycloidal disk at a higher rate. The input shaft rotates nine times to complete a full rotation. The ring gear is designed to correct the dynamic imbalance.
CZPT cycloidal gearheads are designed for precision and stable operation. These reducers are robust and can handle large translocations. They also offer high overload protection. They are suitable for shock wave therapy. CZPT gearheads are also well suited for applications with critical positioning accuracy. They also require low assembly and design costs. They are designed for long service life and low hysteresis loss.
CZPT cycloidal reducers are used in a variety of industrial applications, including CNC machining centers, robot positioners and manipulators. They offer a unique design that can handle high forces on the output axis, and are especially suitable for large translocations. These gearheads are highly efficient, reducing costs, and are available in a variety of sizes. They are ideal for applications that require millimetre accuracy.
High reduction ratios
Compared to other gearboxes, cycloidal gearboxes offer high reduction ratios and small backlash. They are also less expensive. Cycloid gearboxes can be used in a variety of industries. They are suitable for robotic applications. They also have high efficiency and load capacity.
A cycloidal gearbox works by rotating a cycloidal disc. This disc contains holes that are bigger than the pins on the output shaft. When the disc is rotated, the output pins move in the holes to generate a steady output shaft rotation. This type of gearbox does not require stacking stages.
Cycloid gearboxes are usually shorter than planetary gearboxes. Moreover, they are more robust and can transmit higher torques.
Cycloid gearboxes have an eccentric cam that drives the cycloidal disc. The cycloidal disc advances in 360deg/pivot/roller steps. It also rotates in an eccentric pattern. It meshes with the ring-gear housing. It also engages the internal teeth of the ring-gear housing.
The number of lobes on the cycloidal disc is not sufficient to generate a good transmission ratio. In fact, the number of lobes must be less than the number of pins surrounding the cycloidal disc.
The cycloidal disc is rotated by an eccentric cam that extends from the base shaft. The cam also spins inside the cycloidal disc. The eccentric motion of the cam helps the cycloidal disc rotate around the pins of the ring-gear housing.
Reducing amplitude of the vibration
Various approaches to reducing amplitude of the vibration in a cycloidal gearbox have been studied. These approaches are based on the kinematic analysis of gearbox.
A cycloidal gearbox is a gearbox that consists of bearings, gears, and an eccentric bearing that drives a cycloidal disc. This gearbox has a high reduction ratio, which is achieved by a series of output shaft pins that drive the output shaft as the disc rotates.
The test bench used in the studies has four sensors. Each sensor acquires signals with different signal processing techniques. In addition, there is a tachometer that acquires variations in rotational velocity at the input side.
The kinematic study of the robotic gearbox was performed to understand the frequency of vibrations and to determine whether the gearbox is faulty. It was found that the gearbox is in healthy operation when the amplitude of the x and y is low. However, when the amplitude is high, it is indicative of a malfunctioning element.
The frequency analysis of vibration signals is performed for both cyclostationary and noncyclostationary conditions. The frequencies that are selected are those that appear in both types of conditions.
Robust against shock loads
Compared to traditional gearboxes, cycloidal gearboxes have significant benefits when it comes to shock loads. These include high shock-load capacity, high efficiency, reduced cost, lower weight, lower friction, and better positioning accuracy.
Cycloid gears can be used to replace traditional planetary gears in applications where inertia is important, such as the transportation of heavy loads. They have a lighter design and can be manufactured to a more compact size, which helps reduce cost and installation expense. Cycloid gears are also able to provide transmission ratios of up to 300:1 in a small package.
Cycloid gears are also suitable for applications where a long service life is essential. Their radial clamping ring reduces inertia by up to 39%. Cycloid gears have a torsional stiffness that is five times higher than that of conventional planetary gears.
Cycloid gearboxes can provide significant improvements in concrete mixers. They are a highly efficient design, which allows for important innovations. They are also ideal for servo applications, machine tools, and medical technology. They feature user-friendly screw connections, effective corrosion protection, and effective handling.
Cycloid gears are especially useful for applications with critical positioning accuracy. For example, in the control of large parabolic antennas, high shock load capacity is required to maintain accuracy. Cycloid gears can withstand shock loads up to 500% of their rated torque.
Inertial effects
Various studies have been conducted to investigate the static problems of gears. However, there is still a need for a proper model to investigate the dynamic behaviour of a controlled system. For this, a mathematical model of a cycloidal gearbox has been developed. The presented model is a simple model that can be used as the basis for a more complex mechanical model.
The mathematical model is based on the cycloidal gearbox’s mechanical construction and has a nonlinear friction characteristic. The model is able to reproduce the current peaks and breaks at standstill. It also considers the stiction effect. However, it does not cover backlash or torsional stiffness.
This model is used to calculate the torque generating current and the inertia of the motor. These values are then compared with the real system measurement. The results show that the simulation results are very close to the real system measurement.
Several parameters are considered in the model to improve its dynamic behaviour. These parameters are calculated from the harmonic drive system analysis. These are torque-generating current, inertia, and the contact forces of the rotating parts.
The model has a high level of accuracy and can be used for motor control. It is also able to reproduce the dynamic behaviour of a controlled system.
editor by CX 2023-05-24
China Cyclo Gear Reducer Reduction Speed Gearbox Supplier Industrial Cycloidal X Wb Series Pinwheel Miniature Wheel Drive Double Shaft Durable Professional Bw Bwd Bld supplier
Solution Description
Cyclo Gear Reducer Reduction Pace Gearbox Supplier Industrial Cycloidal X WB Sequence PinWheel Miniature Wheel Push Double Shaft Sturdy Expert BW BWD BlD
X / B series substantial good quality cycloidal gearbox small planetary reducer
Swift Information:
Kind: XB sequence Cycloidal Pin Wheel Speed Reducer
Input Velocity: one thousand-1500rmp
Output Velocity: .3-280rpm
Certification: ISO9001 CE
Ex Energy:.09-132KW
Guarantee: 1Years
| Product Identify | X/B sequence Cycloidal Pin Wheel Velocity Reducer |
| The Gear Material | GCR15 |
| The situation Materials | Forged Iron |
| Shade | Blue,Inexperienced, or Customized |
| HS Code | 84834090 |
| Product | X3 |
| Shipping and delivery time | 7-10days |
| Brand | TIANGOU |
|
/ Piece | |
100 Pieces (Min. Order) |
###
| Application: | Motor, Electric Cars, Motorcycle, Machinery, Marine, Agricultural Machinery, Car |
|---|---|
| Function: | Distribution Power, Clutch, Change Drive Torque, Change Drive Direction, Speed Changing, Speed Reduction, Speed Increase |
| Layout: | Coaxial |
| Hardness: | Hardened Tooth Surface |
| Installation: | Horizontal Type |
| Step: | Three-Step |
###
| Samples: |
US$ 9999/Piece
1 Piece(Min.Order) |
|---|
###
| Product Name | X/B series Cycloidal Pin Wheel Speed Reducer |
| The Gear Material | GCR15 |
| The case Material | Cast Iron |
| Color | Blue,Green, or Customized |
| HS Code | 84834090 |
| Model | X3 |
| Delivery time | 7-10days |
| Brand | TIANGOU |
|
/ Piece | |
100 Pieces (Min. Order) |
###
| Application: | Motor, Electric Cars, Motorcycle, Machinery, Marine, Agricultural Machinery, Car |
|---|---|
| Function: | Distribution Power, Clutch, Change Drive Torque, Change Drive Direction, Speed Changing, Speed Reduction, Speed Increase |
| Layout: | Coaxial |
| Hardness: | Hardened Tooth Surface |
| Installation: | Horizontal Type |
| Step: | Three-Step |
###
| Samples: |
US$ 9999/Piece
1 Piece(Min.Order) |
|---|
###
| Product Name | X/B series Cycloidal Pin Wheel Speed Reducer |
| The Gear Material | GCR15 |
| The case Material | Cast Iron |
| Color | Blue,Green, or Customized |
| HS Code | 84834090 |
| Model | X3 |
| Delivery time | 7-10days |
| Brand | TIANGOU |
How to Use a Cyclone Gearbox
Often, a cycloidal gearbox is used in order to achieve a torque transfer from a motor or pump. This type of gearbox is often a common choice as it has a number of advantages over a regular gearbox. Its main advantage is that it is easy to make, which means that it can be incorporated into a variety of applications. However, if you want to use a cycloidal gearbox, there are a few things that you need to know. These include the operation principle, the structure and the dynamic and inertial effects that come with it.
Dynamic and inertial effects
Several studies have been carried out on the static and dynamic properties of cycloidal gears. The study of these effects is beneficial in assisting optimal design of cycloidal speed reducers.
In this paper, the dynamic and inertial effects of a two-stage cycloidal speed reducer have been investigated using the CZPT program package. Moreover, a new model for cycloidal reducers based on non-linear contact dynamics has been developed. The new model aims to predict several operational conditions.
The normal excitation contact force for the cycloid discs of the first and second stage is very similar. However, the total deformation at the contact point is different. This effect is mainly due to the system’s own oscillations. The cycloid discs of the second stage turn around the ring gear roller with a 180deg angle. This angle is a significant contributor to the torque loads. The total excitation force on the cycloid discs of first and second stage is 1848 N and 2068.7 N, respectively.
In order to analyze the contact stress, different gear profiles were investigated. The mesh density was considered as an important design criterion. It was found that a bigger hole reduces the material content of the cycloidal disc and results in more stresses.
Moreover, it is possible to reduce the contact forces in a more efficient manner by changing the geometric parameters. This can be done by mesh refinement along the disc width. The cycloidal disc has the greatest influence on the output results.
The efficiency of a cycloidal drive increases with the increase in load. The efficiency of a cycloidal reducer also depends on the eccentricity of the input shaft and the cycloidal plate. The efficiency curve for small loads is linear. However, for the larger loads, the efficiency curve becomes more non-linear. This is because the stiffness of the cycloid reducer increases as the load increases.
Structure
Despite the fact that it looks like a complicated engineering puzzle, the construction of a cycloidal gearbox is actually quite simple. The key elements are the base, the load plate and the thrust bearing. All these elements work together to create a stable, compact gearbox.
The base is a circular section with several cylindrical pins around its outer edge. The pins are fixed on a fixed ring that holds them in a circular path. The ring serves as a reference circle. The circle’s size is approximately 5mm in diameter.
The load plate is a series of threaded screw holes. These are arranged 15mm away from the center. These are used to anchor external structures. The load plate must be rotated around the X and Y axis.
The thrust bearing is placed on top of the load plate. The bearing is made of an internal diameter of 35mm and an external diameter of 52mm. It is used to allow rotation around the Z axis.
The cycloidal disc is the centerpiece of the cycloidal gearbox. The disc has holes for the pins that drive the output shaft. The holes are larger than those used in output roller pins. The disc also has a reduced eccentricity.
The pins are attached to the cycloidal disc by rolling pins. The pins are made of a material that provides mechanical support for the drive during high-torque situations. The pins have a 9mm external diameter. The disc has a number of lobes and is rotated by one lobe per shaft revolution.
The cycloidal gearbox also has a top cover that helps keep the components together. The cover has a pocket for tools. The top cover also has threads that screw into the casing.
Operation principle
Among many types of gear transmissions, cycloidal gearboxes are used in heavy machinery and multi-axis robots. They are highly effective, compact and capable of high ratios. In addition, they have an overload capability.
Cycloid disks are driven by eccentric shafts that rotate around fixed ring pins. Roller pins of the pin disc engage with holes in the cycloidal disc. These roller pins drive the pin disc and the pin disc transfers the motion to the output shaft.
Unlike conventional gear drives, cycloidal drives have low backlash and high torsional stiffness. They are ideally suited to heavy loads and all drive technologies. The lower mass and compact design of the cycloidal disk also contributes to its high efficiency and positioning accuracy.
The cycloidal disc plays a central role in the gearbox kinematics. It rotates around a fixed ring in a circle. When the disc is pushed against the ring gear, the pins engage with the disc and the roller pins rotate around the pins. This rotating motion generates vibration, which travels through the driven shafts.
Cycloid discs are typically designed with a short cycloid, so that the eccentricity is minimized. This reduces unbalance forces at high speeds. Ideally, the number of lobes on the cycloid is smaller than the number of surrounding pins. This reduces the amount of Hertzian contact stress.
Unlike planetary gears, cycloidal gears have high accuracy and are capable of withstanding shock loads. They also experience low friction and less wear on tooth flanks. They also have higher efficiency and load capacity.
Cycloid gears are generally more difficult to manufacture than involute gears. Cycloid gears are not suitable for stacking gear stages. They require extreme accuracy for manufacturing. However, their smaller size and low backlash, high torsional stiffness, and low vibration make them ideal for use in heavy machines.
Involute gear tooth profile
Almost all gears are manufactured with an involute gear tooth profile. Cycloid gears are also produced with this profile. Compared with involute gears, cycloid gears are stronger and can transmit more power. However, they can also be more difficult to manufacture. This makes them costlier.
The involute gear tooth profile is a smooth curve. It is derived from the involute curve of a circle. A tangent to the base circle is the normal at any point of an involute.
This curve has properties that allow the involute gear teeth to transfer motion in perpendicular direction. It is also the path traced by the end of the string unwrapping from a cylinder.
An involute profile has the advantage of being easy to manufacture. It also allows for smooth meshing despite misalignment of the centre distance. This profile is also preferred over a cycloid tooth profile, but it is not the best in every regard.
Cycloid gear teeth are also made of two curves. Unlike involute teeth, cycloid gear teeth have a consistent radius. Cycloid gears are less likely to produce noise. But they are also more expensive to manufacture.
Involute teeth are easier to manufacture because they have only one curve. Cycloid gears can also be made with a rack type cutter. This makes them cheaper to manufacture. However, they require an expert design. They can also be manufactured with a gear shaper that includes a pinion cutter.
The tooth profiles that satisfy the law of gear-tooth action are sometimes called conjugate profiles. The involute profile is the most common of these. It allows for constant torque transmission.
Backlash
Typically, cycloidal drives provide a high ratio of transmission with no backlash. This is because the cycloid disc is driven by an eccentric shaft. During rotation, the cycloid disc rotates around a fixed ring. This ring also rotates independently of the center of gravity.
The cycloid disc is typically shortened to reduce the eccentricity. This helps to minimize the unbalance forces that may occur at high speeds. The cycloid also offers a larger gear ratio than traditional gears. This provides a better positional accuracy.
Cycloid drives also have a high torsional stiffness. This provides greater torsional resilience and shock load capabilities. This is important for a number of reasons, such as in heavy-duty applications.
Cycloid drives also have lower mass. These benefits make them ideally suited for all drive technologies. The design also allows for higher torsional stiffness and service life. These drives also have a much smaller profile.
Cycloid drives are also used to reduce speed. Because of the high torsional stiffness of the cycloid, they also have high positioning accuracy.
Cycloid drives are well-suited to a variety of applications, including electric motors, generators, and pump motors. They are also highly resistant to shock loads, which is important in a variety of applications. This design is ideal for applications that require a large transmission ratio in a compact design.
Cycloid drives also have the advantage of minimizing the clearance between the mating components. This helps to eliminate interference and ensure a positive fit. This is particularly important in gearboxes. It also allows for the use of a load cell and potentiometer to determine the backlash of the gearbox.
editor by CX 2023-04-03
China High Torque Precision Robot Arm Joint Rv Gearbox Reducer Cycloidal pin wheel harmonic Reduction Gear gearbox design
Warranty: 1 yr
Applicable Industries: Other
Excess weight (KG): 35
Tailored help: OEM, ODM, OBM
Gearing Arrangement: Worm
Output Torque: 10 N.M–55mm and gradually understand the smart products generation line .Our goods are widely used in textile machine、printing machine、food machine、medical machine、convey machine、packaging machinery、work grasp machine、vending machine、 cement machine、computer flat knitting machine、automatic table、office equipment and solar photovoltaic equipment and so on .Our goods are popularly marketed in domestic marketplaces and foreign markets this kind of as Southeast Asia、 India、Europe、America、Middle East and Australia and so forth. The sales quantity carries on to increase at a charge of far more than forty% for each yearWe passed ISO9001、CE 、UL、CCC and ROHS certification and many others..We can fulfill you with the industry’s initial technology ,top quality and fast services help .Honest cooperation with you to construct lovely Backyard .Welcome to go to our factoryHangZhou HENGTUO MOTOR CO.,LTDADD: N0.108,SHANGYEJIA Highway NORTH,HUSHAN Avenue, HangZhou,HangZhou Town,ZHangZhouG PROVINCE,CHINA. Certifications FAQ Q: Are you gear motors company ?A: Of course we are factory.Q: Where are your manufacturing unit ?A: HangZhou, HangZhou, Near ZheJiang cityQ: How several employee in your manufacturing unit ?A: 158 staff.Q: How to buy?A: Send us inquiry → Receive our quotation → Negotiate particulars → Validate the sample → Indicator contract/deposit → Mass production→Cargo all set → Equilibrium/shipping and delivery → Additional cooperationQ: How about Sample buy?A: Sample is offered for you. you should speak to us for details. As soon as we charge you sample fee, please feel straightforward, it would be refundwhen you spot formal get.Q: Which ship way is accessible?A: DHL, UPS, FedEx, TNT, EMS, China Submit,Sea are available.The other shipping and delivery ways are also offered, make sure you contact us if youneed ship by the other shipping way. Q: How long is lead time ?A: Deliver time depends on the quantity you get. usually lead time will take 3-5 doing work times.
Types of Gearboxes
There are several types of gearboxes. Some are known as helical gear reducers, while others are called planetary gearboxes. The article also discusses Continuously Variable Transmission (CVT) and helical gear reducer. If you are interested in purchasing a new gearbox, make sure to read our articles on these different types. If you are confused, consider reading our articles on planetary gearboxes and helical gear reducers.
planetary gearbox
The planetary gearbox has several advantages. Its compact design and light weight allows it to transmit high torques while remaining quiet. The gears are connected to one another through a carrier, which is typically fixed and helps transmit torques to the output shaft. Its planetary structure arrangement also reduces backlash and provides high rigidity, which is important for quick start and stop cycles and rotational direction change. Depending on the design and performance desired, planetary gearboxes are categorized into three main types:
The type of planetary gears used in a given application determines the overall cost of the unit. Manufacturers offer a range of prices, and they can help you determine which gearbox is right for your needs. You should also ask a manufacturer for the cost of a planetary gearbox. By asking about price and specs, you can avoid wasting money and time on a planetary gearbox that does not perform up to its potential.
A planetary gearbox is probably installed in your new car’s automatic transmission. For more information, consult your owner’s manual or call the dealer’s service department. This type of gearbox is more complex than other types of gearboxes, so if you don’t know much about them, do an internet search for “planetary gearbox.”
The teeth of a planetary gearbox are formed by the stepping motion of two gears: the sun gear and the inner ring. The sun gear is the input, while the planetary gears rotate around the sun gear. Their ratio depends on the number of teeth and the space between the planets. If you have a 24 tooth sun gear, the planetary gears’ ratio will be -3/2. The sun gear is also attached to the axle.
Another advantage of a planetary gear system is that it can generate high torques. The load is shared among multiple planet gears. This makes the gears more resilient to damage. A planetary gearbox can be as high as 332,000 Nm, and can be used in vehicles and industrial applications requiring medium to high torque. A planetary gear system is a great alternative to a traditional transmission. So, how does it work?
helical gearbox
The main difference between the helical gearbox and the spur gear is the center distance between the teeth. The helical gearbox has a larger pitch circle than the spur gear and thus requires a radial module. In addition, the two types of gears can only be made with the same tooth-cutting tool as the spur gear. However, the helical gearbox is more efficient in terms of production costs.
The helical gearbox is a low-power consumption, compact type of gearbox that is used for a wide range of industrial applications. They are highly durable and withstand high loads with utmost efficiency. The helical gearbox can be manufactured in cast steel and iron for small and medium units. This type of gearbox is also commonly used for crushers, conveyors, coolers, and other applications that need low power.
The helical gear has many advantages over the spur gear. It produces less noise. It has less friction and is less likely to wear out. It is also quieter than spur gears. This is because multiple teeth are in mesh. Because the teeth are in mesh, the load is distributed over a larger area, resulting in a smoother transition between gears. The reduction in noise and vibration reduces the risk of damaging the gear.
The helical gear’s axial excitation force is obtained using a linearized equation of motion in the rotational direction. The damping coefficient of the equation is 0.07. The helical gear is made up of a steel shaft with a diameter of 20 mm and a 5 mm thick aluminum plate. The stiffness of the bearing is 6.84 x 107 N/m. The damping force of the plate is 2,040 kg/m2/s.
The worm gearbox has a better efficiency ratio than the helical one, but it is less efficient in low-ratio applications. In general, worm gearboxes are more efficient than helical gearboxes, although there are some exceptions to this rule. A helical gearbox is better for applications that require high torque. It may also be more economical in the long run. If you are considering a helical gearbox, consider the advantages it has over worm gearboxes.
helical gear reducer
A helical gear reducer for a machine’s gearbox is an integral component of the drive system. This unit amplifies torque and controls speed and, therefore, compliments the engine by rotating slower than the engine’s input shaft. A helical gear reducer is a compact gearbox component that is used in industrial applications. A variety of sizes is available to suit various machine configurations. The following sections will discuss some of the different types available.
Designed by experts and engineers, a helical gear reducer is a surprisingly small and light gear that satisfies the needs of many machine applications. It features a large transmission torque, a low starting and running speed, and a fine classification of transmission ratios. A helical gear reducer is lightweight and easily connected to other gears, and it features a high technical content.
In order to avoid errors and poor performance, regular maintenance is a must. The proper lubrication of the gear reducer can minimize failures, errors, and poor performance. Every gear reducer manufacturer sells a suitable lubricant, which must match the properties of the machine’s drive mechanism. It is also advisable to check the lubrication regularly to avoid any deterioration of the unit’s performance.
While the worm gearbox may be better for applications where torque is high, the helical gear reducer offers greater efficiency at lower cost. Although worm gearboxes may be cheaper initially, they are less effective at higher ratios. Even if the worm gear is more expensive to buy, it still offers 94% efficiency, which makes it more cost-effective. There are some significant advantages to both types of gearboxes.
The main advantage of a helical gear reducer over a spur gear is its smoother operation. Unlike spur gears, which have teeth that are straight, helical gears have angled teeth that gradually engage with each other. This helps ensure that the gear does not grind or make excessive noise when it turns. Additionally, they are less commonly used in automation and precision machinery. They are often used in industrial applications.
Continuously variable transmission
A Continuously Variable Transmission (CVT) is an automatic transmission that can run through a vast number of gears. Unlike a standard automatic transmission, it can run at any speed, even at a low rev. The CVT is also capable of running at infinitely low gears. Its basic function is to provide different torque ratios to the engine. In addition to delivering power, CVTs have other benefits.
One of the major advantages of a CVT is its simplicity. Its simplicity translates into fewer moving parts, which means less maintenance. The CVT’s simplicity also means that it can handle a wide variety of different types of road conditions and driving styles. In addition to being a great alternative to a traditional automatic transmission, CVTs can be used on many other types of vehicles, including tractors, snowmobiles, motor scooters, and power tools.
A CVT is much smoother than a conventional automatic transmission. It never has to hunt for a gear. It also responds well to throttle inputs and speed changes. Both of these technologies are available on many modern vehicles, including the Nissan Rogue and Mazda CX-5. It’s important to note that each of these transmissions has its pros and cons. So, if you’re looking for a car with a CVT, make sure to read the reviews. They’ll help you decide which transmission is right for you.
Another advantage of a CVT is its fuel efficiency. Many cars now feature CVTs, and they’re becoming increasingly popular with automakers. In addition to fuel efficiency, most cars with CVTs also have a smoother ride. There’s no more sudden downshifts or gear hunting. This makes driving a lot easier. And, the added benefits of smoother driving make CVTs the ideal choice for many drivers.
Although a CVT is more common among Japanese car manufacturers, you’ll find CVTs on European car models as well. The Mercedes-Benz A-Class, B-Class, and Megane are some examples of vehicles that use this technology. Before making a decision, consider the reliability of the model in question. Consumer Reports is a good resource for this. It also offers a history of use and reliability for every type of car, including the Honda Accord.
editor by czh 2023-02-17
China Alunimun Alloy Material Made Worm and Wheel Transmission Gearbox for Agricultural Equipment/Machinery cycloidal pin gear reducer
Product Description
1.SMRV worm gearing arrangement gearmotors created in our manufacturing unit are the Motovario model NMRV collection. The models are NMRV571,030,040,050,063,075,090,one hundred ten,a hundred thirty,150.The min ratio of one unit is 5:1 for SMRV040,050 & 063,and 7.5:1 for other designs. 100:1 is the max ratio for solitary device of gearmotor
two.SMRV gearmotors can be combined by distinct designs or the exact same product to acquire a increased reduction ratio,output torque to the real requests
three.These designs are manufactured to IEC normal specs.
four.Customising is accessible for flanges,& shafts
five.Dependent on motor coupling,the gearmotors are labeled as SMRV,SRV,SMRV-E,SRV-E as the picture exhibits as follows,
6.Guarantee: 1 calendar year following cargo,on proper procedure situations
seven. Package.
Every single unit is wrapped in plastic bag,then in carton box,and numerous carton packing containers are packed in wooden pallet.
eight. Shipping and delivery approaches,by sea,by air,or by DHL
nine.Samples and payment,
Samples are charged and be compensated by the consumer,but it will be refundable by means of deduction from the payment of the purchase afterwards.
|
US $25 / Piece | |
1 Piece (Min. Order) |
###
|
Shipping Cost:
Estimated freight per unit. |
To be negotiated| Freight Cost Calculator |
|---|
###
| Layout: | Cycloidal |
|---|---|
| Hardness: | Hardened Tooth Surface |
| Installation: | Vertical Type |
###
| Samples: |
US$ 30/Piece
1 Piece(Min.Order) |
|---|
###
| Customization: |
Available
|
|---|
|
US $25 / Piece | |
1 Piece (Min. Order) |
###
|
Shipping Cost:
Estimated freight per unit. |
To be negotiated| Freight Cost Calculator |
|---|
###
| Layout: | Cycloidal |
|---|---|
| Hardness: | Hardened Tooth Surface |
| Installation: | Vertical Type |
###
| Samples: |
US$ 30/Piece
1 Piece(Min.Order) |
|---|
###
| Customization: |
Available
|
|---|
Cyclone Gearbox Vs Involute Gearbox
Whether you’re using a cycloidal gearbox or an involute gearbox for your application, there are a few things you should know. This article will highlight some of those things, including: cycloidal gearbox vs involute gearbox, weight, compressive force, precision, and torque density.
Compressive force
Several studies have been carried out to analyze the static characteristics of gears. In this article, the authors investigate the structural and kinematic principles of a cycloidal gearbox. The cycloidal gearbox is a gearbox that uses an eccentric bearing inside a rotating frame. It has no common pinion-gear pair, and is therefore ideal for a high reduction ratio.
The purpose of this paper is to investigate the stress distribution on a cycloidal disc. Various gear profiles are investigated in order to study the load distribution and dynamic effects.
Cycloidal gearboxes are subject to compression and backlash, which require the use of proper ratios for the bearing rate and the TSA. The paper also focuses on the kinematic principles of the reducer. In addition, the authors use standard analysis techniques for the shaft/gear and the cycloidal disc.
The authors previously worked on a rigid body dynamic simulation of a cycloidal reducer. The analysis used a trochoidal profile on the cycloidal disc periphery. The trochoidal profile is obtained from a manufacturing drawing and takes into account the tolerances.
The mesh density in the cycloidal disc captures the exact geometry of the parts. It provides accurate contact stresses.
The cycloidal disc consists of nine lobes, which move by one lobe per rotation of the drive shaft. However, when the disc is rotated around the pins, the cycloidal disc does not move around the center of gravity. Therefore, the cycloidal disc shares torque load with five outer rollers.
A low reduction ratio in a cycloidal gearbox results in a higher induced stress in the cycloidal disc. This is due to the bigger hole designed to reduce the material inside the disc.
Torque density
Several types of magnetic gearboxes have been studied. Some magnetic gearboxes have a higher torque density than others, but they are still not able to compete with the mechanical gearboxes.
A new high torque density cycloidal magnetic gearbox using Halbach rotors has been developed and is being tested. The design was validated by building a CPCyMG prototype. The results showed that the simulated slip torque was comparable to the experimental slip torque. The peak torque measured was a p3 = 14 spatial harmonic, and it corresponds to the active region torque density of 261.4 N*m/L.
This cycloidal gearbox also has a high gear ratio. It has been tested to achieve a peak torque of 147.8 Nm, which is more than double the torque density of the traditional cycloidal gearbox. The design incorporates a ferromagnetic back-support that provides mechanical fabrication support.
This cycloidal gearbox also shows how a small diameter can achieve a high torque density. It is designed with an axial length of 50mm. The radial deflection forces are not serious at this length. The design uses a small air gap to reduce the radial deflection forces, but it is not the only design option.
The trade-off design also has a high volumetric torque density. It has a smaller air gap and a higher mass torque density. It is feasible to make and mechanically strong. The design is also one of the most efficient in its class.
The helical gearing design is a newer technology that brings a higher level of precision to a cycloidal gearbox. It allows a servomotor to handle a heavy load at high cycle rates. It is also useful in applications that require smaller design envelopes.
Weight
Compared to planetary gearboxes, the weight of cycloidal gearboxes is not as significant. However, they do provide some advantages. One of the most significant features is their backlash-free operation, which helps them deliver smooth and precise movement.
In addition, they provide high efficiency, which means that servo motors can run at higher speeds. The best part is that they do not need to be stacked up in order to achieve a high ratio.
Another advantage of cycloidal gearboxes is that they are usually less expensive than planetary gearboxes. This means that they are suitable for the manufacturing industry and robotics. They are also suited for heavy-duty robots that require a robust gearbox.
They also provide a better reduction ratio. Cycloidal gears can achieve reduction ratios from 30:1 to 300:1, which is a huge improvement over planetary gears. However, there are few models available that provide a ratio below 30:1.
Cycloidal gears also offer more resistance to wear, which means that they can last longer than planetary gears. They are also more compact, which helps them achieve high ratios in a smaller space. The design of cycloidal gears also makes them less prone to backlash, which is one of the major shortcomings of planetary gearboxes.
In addition, cycloidal gears can also provide better positioning accuracy. In fact, this is one of the primary reasons for choosing cycloidal gears over planetary gears. This is because the cycloid disc rotates around a bearing independently of the input shaft.
Compared to planetary gearboxes, cycloidal gears are also much shorter. This means that they provide the best positioning accuracy. They are also 50% lighter, meaning that they have a smaller diameter.
Precision
Several experts have studied the cycloidal gearbox in precision reducers. Their research mainly focuses on the mathematical model and the method for precision evaluation of cycloidal gears.
The traditional modification design of cycloidal gears is mainly realized by setting various machining parameters and center position of the grinding wheel. But it has some disadvantages because of unstable meshing accuracy and uncontrollable tooth profile curve shape.
In this study, a new method of modification design of cycloidal gears is proposed. This method is based on the calculation of meshing backlash and pressure angle distribution. It can effectively pre-control the transmission accuracy of cycloid-pin gear. It can also ensure good meshing characteristics.
The proposed method can be applied in the manufacture of rotary vector reducers. It is also applicable in the precision reducer for robots.
The mathematical model for cycloidal gears can be established with the pressure angle a as a dependent variable. It is possible to calculate the pressure angle distribution and the profile pressure angle. It can also be expressed as DL=f(a). It can be applied in the design of precision reducers.
The study also considers the root clearance, the backlash of gear teeth and the profile angle. These factors have a direct effect on the transmission performance of cycloidal gear. It also indicates the higher motion accuracy and the smaller backlash. The modified profile can also reflect the smaller transmission error.
In addition, the proposed method is also based on the calculation of lost motion. It determines the angle of first tooth contacts. This angle is an important factor affecting the modification quality. The transmission error after the second cycloid method is the least.
Finally, a case study on the CZPT RV-35N gear pair is shown to prove the proposed method.
Involute gears vs cycloidal gears
Compared to involute gears, cycloidal gears have a lower noise, less friction, and last longer. However, they are more expensive. Cycloidal gears can be more difficult to manufacture. They may be less suitable for certain applications, including space manipulators and robotic joints.
The most common gear profile is the involute curve of a circle. This curve is formed by the endpoint of an imaginary taut string unwinding from the circle.
Another curve is the epicycloid curve. This curve is formed by the point rigidly attached to the circle rolling over another circle. This curve is difficult to produce and is much more expensive to produce than the involute curve.
The cycloid curve of a circle is also an example of the multi-cursor. This curve is generated by the locus of the point on the circle’s circumference.
The cycloid curve has the same diameter as the involute curve, but is tangentially curving along the circle’s diameter. This curve is also classified as ordinary. It has several other functions. The FE method was used to analyze the strain state of cycloidal speed reducers.
There are many other curves, but the involute curve is the most widely used gear profile. The involute curve of a circle is a spiraling curve traced by the endpoint of an imaginary tautstring.
Involute gears are a lot like a set of Lego blocks. They are a lot of fun to play with. They also have a lot of advantages. For example, they can handle center sifts better than cycloidal gears. They are also much easier to manufacture, so the cost of involute teeth is lower. However, they are obsolete.
Cycloidal gears are also more difficult to manufacture than involute gears. They have a convex surface, which leads to more wear. They also have a simpler shape than involute gears. They also have less teeth. They are used in rotary motions, such as in the rotors of screw compressors.
editor by czh 2022-12-31
OEM made in China – replacement parts – in Kampala Uganda T120 4G41 Mt043664 7X37 Crown Wheel Pinion Gear with ce certificate top quality low price
We – EPG Team the bigge EPT Chain and agricultural gearbox manufacturing unit in China with 5 various branches. For more information: Cellular/whatsapp/telegram/Kakao us at: 0086~13083988828 13858117778 0571 88828
OEM T120 4G41 MT57164 7X37 crown wheel pinion gear
Our gear can be regular as per European or American standard or unique as for each your drawing or sample.
Functions:
♦ Material: carbon metal this sort of as C45, 20CrMnTi, 40Cr, 42CrMo or stainless steel or copper or nylon and so on
♦ Heat Remedy: Hardening and Tempering, High Frequency Quenching, Carburizing Quenching and so on.
♦ Standard: European or American standard
♦ Item: M0.5,M1 .M1,5,M1,7,M2,M2.5,M3,M4,M5,M6 and so on
♦ Export Area: Europe and The united states
♦ OEM provider: make based on your special sample or drawing and satisfy your need for high precision on teeth of gear
Good quality with reasonable price, well timed supply and wonderful buyer services.
We can also source spur gear,special gears, worm gear,worm wheel,gear spiral bevel gears, massive spur gears,gears wheel,straight bevel gears, helical bevel gears,spur gears,planetary gears, passive gears, milled spur gears, gear for valve,
truck gear, transmission spur gear,spur bearing equipment, equipment pinions,galvanized equipment ect offered. Common or unique gears produced by CNC device
We make equipment as for every your particular samples or drawing and we also produce as for each regular such as Metric standard, British standards, AGMA requirements by CNC device
Substance can be C45, 40Cr, 20CrMnTi, 42CrMo, copper, stainless metal and so on as for every your requests
There is large precision accessible as your special ask for
Our gear is exported to Europe and The usa in massive amount and so we are certain that we can assist you get great success!
Crown wheel pinion, crown wheel and pinion, crown wheel & pinion, crown wheel gears, crown pinion, pinion and crown wheel, crown pinion suppliers, Crown Wheel Pinion Equipment, China Crown Wheel Pinion Equipment, pinion and crown wheel
We have previously exported our products for far more than twenty a long time, as a professional provider, we have more than 200 sorts of ring and pinion equipment, they are for automobile, bus and truck, our major market consist of Europe, The united states, Middle East, Southea EPT Asia, Africa and Russia, We obtain fantastic status with certain high quality and aggressive price tag.
See the beneath our crown wheel and pinion varieties for validate, if any need, you should do not wait to get in touch with with US.
MITSUBISHI Crown Wheel Pinion MB005252 6X37 4D31/PS100/canter
MB161192 6X40 4D31/PS100/canter
MC835114/MC863589 6X37 4D34/PS120/canter
MB863590 6X40 4D34/PS120/canter
MITSUBISHI crown wheel and pinion PS190 6D16 FM517 MB839939 6X40 PS190/FUSO
FM517 MC817479 6X37 PS190/FUSO
FM517 MC-839938-A 6*forty three
MITSUBISHI 120S L300G MB527152 7X37
MITSUBISHI 4D55 L300D MB241981 7X37
MITSUBISHIPS135 MC57131 6X37
6*40
MITSUBISHI T120 4G41 MT57164 7X37
MITSUBISHI PS100 4D31 MB308059 EPT Gear
MB308115 Solar Equipment
MB161186 Differ
MITSUBISHI PS100 4D34 Vary
MITSUBISHI PS100 MB 308116 Sun Gear
MB 308115 EPT Equipment
MITSUBISHI PS120 MC825365 Solar Equipment
MC 835982 EPT Equipment
MITSUBISHI PS100 COUTER SHAFT ME-603213
MITSUBISHI PS120 COUTER SHAFT ME-603214
MITSUBISHI COUTER SHAFT ME-604431
ME-60571
MC866747 8X39
MC805654
MITSUBISHI 8DC9 Front MC8 0571 4 6X40 6D22/FUSO
MITSUBISHI 8DC9 REAR MC8 0571 6X40 6D22/FUSO
MITSUBISHI 8DC9 FV313FR 12571-55040 6X41
MITSUBISHI 8DC9 FV313RR 12571-90040 6X41
MITSUBISHI 6D15 MC806120 6X40 FN516/FUSO
MITSUBISHI FP320 MC831408 MID(Center) 7X39 6D40
MC831408REAR(REAR) 7X39 6D40
MITSUBISHI FP415 MC827154REAR(REAR) 7X39 8DC11/FUSO
MC827154MID(Center) 7X39 8DC11/FUSO
MC834742(SPLINE/22) 8X39
MC834990(SPLINE/20) 8X37
MC834996/MC836736/MC834991 (SPLINE/20) 8X39
ME508242 7X39
6X41
MITSUBISHI 6D22 Front MC8571/808508 6X45 FN527/GENZO
MITSUBISHI 6D22 REAR MC57154(MC809464/808505) 6X45 FN527/GENZO
MB598487 8X39
MR179199 11X51
MR162750 11X51
Toyota crown wheel and pinion RINO HT 41201-85719 7X45
Toyota RINO 14-B 41201-39495 6X39
41201-39495-S 6X41
Toyota RINO LT 41201-80187 6X35
41201-85717/16HOL EPT 6*35
Toyota HILUX Crown Wheel Pinion 41201-39696 8X39
41201-29536-S 9X41
41201-87613 11X39
41201-87615 11X37
Toyota COASTER crown wheel gears 6X35 MINIBUS
6X37 MINIBUS
6X41 MINIBUS
7X39 MINIBUS
8X41 MINIBUS
Toyota LAND CRUISER 41201-69355 9X37
41201-69167
ISUZU Crown Wheel Pinion 8-97 0571 seventy three- 10X41
eight-94225-258-1 9X41
1-4121571- 7X43
1-4121 0571 – 7X43
ISUZU NKR 8-97047-092-1 6X41
ISUZU NPR 8-97571-310 7X43
8-97571-741 7X41
8-97571-639 6X39
ISUZU FTR 47210-2750 6X41
47210-2760 6X39
7X43
Nissan Front CK12 38110-95715(38110-90404) 6X41 CWA fifty three/PE6/RD8
Nissan REAR CK12 38110-90116(38110-90369) 6X41 CK12/PE6/RD8
38110-90115 6*37 CPB12
38110-90113/38110-9571 7*36 PD6
38110-91003/31th tooth 6*41
38110-9571 6X41 CWB520NEW
38110-90502 6X41 CWB520NEW
38110-9571 5X37
38110-90501 5X37
38110-90707 7X39 RF8/DJ502
38110-90708 7X39 RF8/DJ502
38110-9571 6X39
38110-90503 6X39
38110-90006 7X39
38110-90007 7X39
HINO Crown Wheel Pinion 41201-1382 7X45 FM226/SG
41201-1163 7X38 EM100
41203-1180 7X43 AKBUS
41201-1080 7X46
41201-1101 6X41 EF750/SG N EPT BOLT
41201-4110 7X41
41201-3790 7X41
41201-4650 7X41
41201-4850 7X41
41201-2991 7X41
HINO Crown Wheel and Pinion 41203-1811 7X44 H07C NEW
41203-2250 7X41 H07C/FL
41201-4571(41201-3070) 7X45 J08C ten-WHL
41201-4040 7X45
41211-2960 7X43
HangZhou EPT Market Co., Ltd. is a specialized provider of a full variety of chains, sprockets, gears, equipment racks, v belt pulley, timing pulley, V-belts, couplings, machined areas and so on.
Owing to our sincerity in providing be EPT services to our customers, understanding of your requirements and overriding feeling of accountability towards filling purchasing demands, we have acquired the tru EPT of purchasers worldwide. Getting accumulated cherished encounter in cooperating with foreign clients, our merchandise are offering nicely in the American, European, South American and Asian markets.Our goods are produced by modern day computerized equipment and gear. In the meantime, our goods are created in accordance to higher top quality requirements, and complying with the global sophisticated common requirements.
With a lot of years’ expertise in this line, we will be trusted by our rewards in aggressive price tag, one-time supply, prompt response, on-hand engineering support and very good soon after-sales companies.
Furthermore, all our manufacturing processes are in compliance with ISO9001 expectations. We also can style and make non-regular items to meet up with customers’ particular specifications. Top quality and credit history are the bases that make a company alive. We will supply be EPT services and higher top quality goods with all sincerity. If you require any info or samples, please contact us and you will have our quickly reply.
The use of first gear manufacturer’s (OEM) portion figures or logos , e.g. CASE® and John Deere® are for reference functions only and for indicating item use and compatibility. Our organization and the outlined substitute components contained herein are not sponsored, approved, or produced by the OEM.
Sprocket made in China – replacement parts – in Villahermosa Mexico Gear Chain Wheel with ce certificate top quality low price
We – EPG Group the bigge EPT Chain and agricultural gearbox manufacturing facility in China with 5 diverse branches. For a lot more specifics: Cellular/whatsapp/telegram/Kakao us at: 0086~13083988828 13858117778 0571 88828
Positive aspects:
one. Specialist gears company
2.Skilled in Cooperate with massive Organizations
3. Professional gears EPT Capacity
4.Stable gears Quality
five.Affordable gears Prices
six.Small gears Orders Recognized
7.Steady gears quality advancements
8. Higher gears good quality Efficiency
9.Limited gears direct time and shipment
ten.Skilled gears services
We can provide with sample for high quality and operate screening.
Product Description:
| Material | Carbon Metal | SAE1571, SAE1045, Cr12, 40Cr, Y15Pb, 1214Letc | |
| Alloy Stee | 20CrMnTi, 16MnCr5, 20CrMnMo, 41CrMo, 17CrNiMo5etc | ||
| Brass/Bronze | HPb59-1, H70, CuZn39Pb2, CuZn40Pb2, C38000, CuZn40etc | ||
| Type | Bevel Gear | ||
| Treatment | Heat remedies, Carburizing, Polishing | ||
| Standard | ISO /R 606 | ||
| Machining procedure | fabrication,stamping,deep drawing,gear hobbing, gear milling, gear shaping, machining and assembly gear broaching, gear grinding and gear gaping | ||
| Module | 1., 1.twenty five, 1.5, 1.75, 2., 2.twenty five, 2.5….8. and so forth | ||
| Tolerance handle | Outer Diameter:±0.005mm | Size Dimension:±0.05 mm | |
| Enamel accuracy | GB1244-85, DIN8188, ISO/R 606 , ANSI B 29.1M | ||
| Heat treatment method | Quenching & Tempering, Carburizing & Quenching, Large-frequency Hardening, Carbonitriding… | ||
| Area treatment | Blacking, Polishing, Anodization, Chrome plating, Zinc plating, Nickel plating… | ||
Our company has a variety of imported high-precision processing gear, sophisticated creation engineering ,increase the implies of detection, a sound item good quality management method, for buyers ca EPT very first-class quality .
Our Provider
1.OEM: According to your drawings and samples needs.
2.Manufacturer with competitive price and high high quality.
three. one hundred% inspection just before delivery.
4. Hassle-free transportation.
5 .Very good packing.
six. Small gears Orders Acknowledged.
7. Rich seasoned staff Professional specialized support and resolution staff
Packaging & Delivery:
Packaging Information: Plastic bag inner and regular carton outer or as per
client’s needs
Shipping and delivery Element: Delivered in 20-30 days after advance TT payment
If there are any questions or need to have our assist, make sure you get in touch with with us with no wait , or you can deliver a message to us .
The use of first products manufacturer’s (OEM) portion quantities or logos , e.g. CASE® and John Deere® are for reference needs only and for indicating item use and compatibility. Our organization and the detailed replacement parts contained herein are not sponsored, approved, or manufactured by the OEM.